Penetration sealing
Pipe and vent flashings are renewed so they move with the roof.
Metal Roofing
Metal Roof Repair Englewood, NJ
A roofer in Englewood can repair a leaking metal roof by replacing dried-out screw washers, resealing panel laps, treating rust and refastening loose trim, and fix it with the right fasteners, sealant and trim for the panel. Dial (551) 355-3321 to talk with a local roofer about the leak.
Most metal roof repairs have nothing to do with the metal itself. Ribbed and corrugated metal relies on hundreds of washered screws, and sun and heat slowly harden the washers until they leak. Panels also expand and contract with every day of heat, which works screws loose and wallows out their holes.
After fasteners, most repairs happen where panels and trim overlap. Side laps and end laps were sealed with butyl tape or sealant that can fail, and ridge caps without foam closures let wind-driven rain blow in under the trim. Rust starts at cut edges, scratches and fastener holes and moves faster where two different metals touch.
Metal roof repair is usually a far smaller job than replacement, as long as the panels are sound. Before calling, note where you see drips or stains, whether they show up during rain or on cool mornings and what kind of panel is on the roof. Stay off the roof, especially when wet or frosty, since painted metal is extremely slick.
If the problem goes deeper than it first looked, an Englewood roofer may also recommend metal roof coating or metal roof inspection.
Looking for Englewood metal roof repair? Call (551) 355-3321 to talk to a local roofer.
Call nowThe process
What happens during a metal roof repair
Here is how a roofer typically approaches a metal roof repair.
Find the leak
The roofer checks the underside from the attic or building interior, then walks the roof along the purlins looking at screws, laps, trim and penetrations. Rust trails and stains on the underside often point straight to the culprit.
Fix the screws
Every leaking screw is pulled and replaced with a new washered fastener, sized up where the hole has worn. Screws that missed the purlin are moved and the old hole sealed.
Reseal the seams
Open side and end laps are cleaned out and resealed so water cannot wick between panels. Sealant has to stay flexible to handle thermal movement.
Treat the rust
Surface rust is wire brushed, primed with a rust-inhibiting primer and painted. The cause of the rust gets fixed along with the rust itself.
Repair the trim
Loose ridge cap, rake trim and wall flashing are refastened, missing foam closures are replaced and cracked pipe boots are swapped for flexible metal roof boots. Single panels are replaced when patching would not hold.
What is included
What metal roof repair covers
Lap sealing
Seams that wick water are resealed with flexible sealant so water cannot travel between panels.
Fastener replacement
Backed-out fasteners are replaced, sized up where needed and driven to the right depth.
Closure replacement
Missing foam closures at the ridge and eaves are replaced to close gaps at the roof edges.
Corrosion treatment
Rust holes are patched with matching metal to keep the panel in service.
Related service
Metal Roof Leak Repair Englewood, NJ
A metal roof leak rarely drips right below its source, which is the first thing a good metal roof leak repair accounts for. Most leaks come from a short list: screws, seams, ridge trim, boots and wall flashing. Each one has a lasting fix, and none of them is a bead of caulk.
In Englewood, metal roof leaks are often noticed late because insulation absorbs the water first. Catch drips in a bucket, and if water is near wiring or fixtures, cut power to that area at the breaker panel when it is safe. Then call a roofer in Englewood to find the source.
Related service
Corrugated Metal Roof Repair Englewood, NJ
Corrugated panels, the classic wavy metal roof, have their own repair habits. Screws go through the face of the panel, so every fastener is a potential leak, and older roofs may use nails that work loose over time. Swapping nails for washered screws stops most leaks on older corrugated roofs.
Individual corrugated panels on Englewood buildings can usually be swapped when one has rusted through. The new panel has to match the corrugation size and lap direction so it nests with the panels around it. Getting the lap direction right keeps wind-driven rain out.
Local help
Metal Roof Repair Near Me
Around Englewood, metal roofs on homes, shops and barns all eventually need fastener and seam work. From Englewood out to neighboring towns such as Englewood Cliffs, Leonia, Tenafly and Bergenfield, corrugated and ribbed panels on older buildings are the usual repair jobs, along with metal re-roofs on homes that are starting to show their first problems, which is why replacing worn fasteners before they leak is the simplest kind of metal roof care.
Need metal roof repair around Englewood? Call (551) 355-3321 for an Englewood roofer who serves the towns around it too.
What the local climate does to a roof
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Englewood, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Smaller repairs
Small roof problems caught early usually stay small repairs.
Local knowledge
Roofers in Englewood know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Metal Roof Repair FAQ
Is my metal roof leaking or is it condensation?
The timing gives it away more than anything. If drips appear without rain, moisture is condensing on the cold metal; if they follow rain, it is a leak. Condensation is solved with a vapor barrier, insulation or ventilation, not roof sealant.
What causes most metal roof leaks?
The screws and their rubber washers cause more metal roof leaks than anything else. Washers dry out and crack, screws back out as the panels expand and contract, and some screws were overdriven or missed the framing. After fasteners come panel laps, ridge trim, boots and flashing.
What is oil canning on a metal roof?
It is the waviness you sometimes see in the flats of metal roof panels. It comes from stresses in the metal, uneven framing or panels fastened too tightly to move, and it is mostly a cosmetic issue that does not cause leaks. Severe cases tied to loose or overtight fastening can be looked at during a repair visit.
Does sealant fix leaking metal roof screws?
Sealant on top of a bad screw usually fails within a season or two. Metal moves, caulk cracks, and the leak returns, so the screw itself gets replaced. Caulk also hides the screw, making the next repair harder.
Can rust on a metal roof be repaired?
Rust that has not eaten through is cleaned, primed and painted. Where rust has gone through, a patch or a new panel is the fix. If rust is widespread, a full roof coating may be worth discussing.
More questions? Call (551) 355-3321
Other services that may help
Metal Roof Coating
Elastomeric and silicone coating systems that renew an aging metal roof, as a step between repair and replacement.
Learn moreMetal Roof Inspection
A close check of the fasteners, seams, finish, trim and flashing on a metal roof, before small fastener problems become leaks.
Learn moreMetal Roof Replacement
Replacing a rusted or worn-out metal roof, or swapping an old shingle roof for new metal, with purlins and decking checked before new panels go on.
Learn moreStanding Seam Metal Roof
Standing seam metal roofs with concealed clips, raised seams and no exposed screws in the panels, for homes, additions and low slope roofs.
Learn more
Looking for something else?
See all roofing servicesNeed metal roof repair in Englewood, NJ?
Call now for Englewood metal roof repair and help in the towns around it.