Drip edge
Bent or missing drip edge is replaced at eaves and rakes to protect the deck edge.
Roof Repair
Flashing Repair Englewood, NJ
A Englewood roofer can stop leaks where the roof meets a wall, dormer, skylight or edge by renewing the flashing at that joint, with the wall sheathing checked for hidden rot. Call (551) 355-3321 to reach a local roofer.
Shingles handle the open field of a roof; flashing handles the joints. Step flashing is a series of small bent pieces woven in with each course of shingles along a sidewall, counter flashing laps over it from the wall side, a kickout at the bottom of the wall throws water into the gutter, and drip edge lines the eaves and rakes. Each of those pieces has one job, and when it fails, water finds the gap.
Flashing leaks are sneaky because the water often runs into the wall instead of the attic. At the base of a roof-to-wall joint, water with nowhere to go runs behind siding and soaks the wall framing. That is why flashing deserves a close look on any house with walls rising above a roof.
Caulk is not flashing. Sealant can hold for a while, but it fails sooner or later, and the joint leaks once more. Lasting flashing repair means new metal installed in the right order, with sealant only as a backup.
If the problem goes deeper than it first looked, an Englewood roofer may also recommend chimney flashing repair or roof leak repair.
Need flashing repair in Englewood? Call (551) 355-3321 to reach a nearby roofing contractor.
Call nowThe process
How flashing repair works
Good flashing work is mostly about the order things overlap.
Check the flashing
The roofer checks the joint from the roof and the attic, looking for missing pieces, rust, face nails and caulk hiding a gap. Soft siding or stained trim below the joint suggests the wall needs a look too.
Open the joint
The shingles next to the wall come up, and the lowest siding courses come off to expose the flashing. Working the new pieces in correctly depends on access behind the siding.
Weave in the metal
Each new step piece overlaps the one beneath it, and the kickout at the base sends water into the gutter. Fasteners go into the roof deck only, never through the vertical leg into the wall.
Add counter flashing
On masonry walls, counter flashing is set into a cut joint; on framed walls, the housewrap and siding cover the flashing. That clearance keeps the siding from soaking up water at the roof line.
Check drip edge
Damaged drip edge is renewed so water drips clear of the fascia. At eaves the underlayment goes over the drip edge; at rakes the drip edge goes over it.
What is included
Flashing a roofer can repair
Step flashing
Step pieces along walls and dormer cheeks are replaced behind the housewrap.
Headwall flashing
Headwall metal at the top of a slope is replaced with proper laps over the shingles.
Diverter flashing
Missing kickout diverters are installed at the base of sidewalls to steer water into the gutter.
Cap flashing
Counter flashing over step pieces is refitted or replaced where the wall and roof meet.
Related service
Roof Flashing Repair Englewood, NJ
Roof flashing repair ranges from resetting a single loose piece to rebuilding a full sidewall. Minor work includes refastening loose metal or adding a missing kickout; bigger jobs mean pulling siding and replacing every step piece along a wall. Knowing the scope up front avoids surprises once siding comes off.
Material matters too. Aluminum is common and easy to form, galvanized steel is stiffer, and copper lasts a very long time; aluminum should not sit directly against fresh mortar or certain treated lumber, which can corrode it. Mixing copper with aluminum or galvanized metal in contact can cause corrosion, so the roofer matches the metal to what is already there.
Related service
Roof Valley Flashing Englewood, NJ
Roof valleys carry the runoff from two slopes, so they handle more water than any other part of the roof. Valleys are either open, with exposed metal, or closed, with shingles running through them. A peel-and-stick underlayment down the valley is the backup layer in both styles.
Common valley problems include rusted metal, debris dams, worn shingles and nails placed too close to the centerline. Uncut shingle corners can catch water and direct it under the roofing. A valley that leaks is generally rebuilt rather than patched.
Local help
Flashing Repair Near Me
Flashing repairs in Englewood are common on houses with dormers, additions and second-story walls rising above lower roofs. Across Englewood and nearby communities including Englewood Cliffs, Leonia, Tenafly and Bergenfield, the age of the house and the number of roof-to-wall joints decide how much flashing work is likely, so a close look at every joint is worth asking for.
Searching for flashing repair near me from Englewood or Englewood Cliffs, Leonia, Tenafly and Bergenfield? Call (551) 355-3321 to talk to a roofer who works in your part of town.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Englewood is busiest after a hard winter and before the next one.
Why call
Why act early
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Englewood
Local roofers see the same roofs and storm damage across Englewood and nearby towns.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about flashing repair
What are the signs of bad roof flashing?
Water showing up near a wall joint, skylight or valley points to flashing. Outside, look for rust, gaps, lifted metal, nails through the face and heavy caulk along the joint. Stained trim where a roof edge meets a wall is a common clue too. A roofer reached at (551) 355-3321 can look at every joint.
Why does flashing need to be woven with the shingles?
Step flashing is a series of small L-shaped pieces, one for each course of shingles along a wall. That layering means every piece sheds water onto the shingle below it, the same way the shingles shed water down the roof. A single long strip of metal along a wall cannot do that and tends to channel water behind the shingles.
Can flashing be repaired without replacing the roof?
Flashing repair is a routine job on roofs that are otherwise sound. Only the shingles and siding next to the joint come off while new metal goes in. If the roof is near the end of its life, it can make sense to replace flashing as part of a reroof instead.
Can I just seal the flashing with caulk?
A bead of caulk may hold for a season or two, but it will fail. Over time, it hardens, splits and lets the joint leak again, often worse than before. A proper repair replaces the metal so it sheds water without depending on sealant.
What is a kickout flashing?
A kickout is a small diverter at the bottom of a roof-to-wall joint, where the roof edge ends against a wall. Its job is to keep the water coming down the joint off the siding and out of the wall. Without one, the wall below that joint often rots quietly for years.
More questions? Call (551) 355-3321
Other services that may help
Chimney Flashing Repair
Repairing the step, counter, apron and back pan flashing where a chimney passes through the roof, instead of another coat of tar.
Learn moreRoof Leak Repair
Stopping water at the pipe boots, flashing, valleys and nail holes where roofs actually leak, with the damage underneath checked too.
Learn moreSkylight Repair
Fixing leaking, fogged or cracked skylights and the flashing around them, so the opening stays dry through every storm.
Learn moreRoof Vent Repair
Vent and pipe boot repairs for leaks, hail damage and worn-out parts, with the attic airflow kept working.
Learn more
Looking for something else?
See all roofing servicesTalk to an Englewood roofer about flashing repair
Call now for Englewood flashing repair and help in the towns around it.